Description
115mm CrazybeeX FR V2.2 F4 AIO ESC 25/200mW VTX 1-2S 3 Inch Toothpick FPV Racing Drone BNF w/1202.5 Motor Caddx ANT 1200TVL Camera Support Insta360 Go
Specification:Â
Item Name: 115mm F4 OSD 1-2S 3 Inch Toothpick FPV Racing Drone;Â
Wheelbase: 115mm;Â
Size: 97x97x35mm (without propellers);Â
Optional Receiver Version:Â
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode);Â
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter);Â
Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio);Â
Weight: 41g (without battery);Â
Recommend Lipo Battery:Â 2s 350mah/400mah/450mah/520mah Battery ( NOT Included).Â
EX1202.5 6400KV Motor –Â
Configu-ration: 9N12P;Â
Stator Diamter: 12mm;Â
Stator Length: 2.5mm;Â
Shaft Diameter: Φ1.5mm;Â
Motor Dimension(Dia.*Len): Φ14*14.5mm;Â
Weight: 4.4g;Â
No.of Cells(Lipo): 1-2S.Â
Gemfan 3018 2-Blade Propeller –Â
Center Thickness: 5.5mm;Â
Prop Diameter: 76.5mm;Â
Center Hole diameter: 1.5mm.Â
CrazybeeX FR V2.2 F4 Flight Controller –Â
MCU: STM32F411CEU6 (100MHZ, 512K FLASH);Â
Sensor: MPU6000 or ICM20689 or BMI270 (SPI connection);Â
Board Size: 28.5×28.5mm;Â
Power Supply: 1-2SÂ battery input (DC 2.9V-8.7V);Â
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready;Â
Built-in Betaflight OSD(SPI Control);Â
Built-in 5.8G VTX;Â
Built-in SPI Frsky/Flysky receiver or no receiver;Â
Built-in 5V 1A BEC;Â
(Frsky SPI RX Version) CRAZYBEEX FRÂ V2.2 FC Â Firmware target: CrazybeeF4FR;Â
(Flysky SPI RX Version) CRAZYBEEX FSÂ V2.2 FC Firmware target: CrazybeeF4FS;Â
(DSM2/X SPI RX Version)CRAZYBEEX DXSÂ V1.0 FC firmware target: CrazybeeF4DXS;Â
(External Frsky RXSR Version)Â CRAZYBEEXÂ PNP V2.2 Firmware target: CrazybeeF4DX;Â
(External TBS CRSF NANO Version)Â CRAZYBEEXÂ PNP V2.2 Firmware target: CrazybeeF4DX.Â
Onboard 5A BL_S 4in1 ESC –Â
MCU upgraded to EFM8BB21;Â
Power supply: 1S LiPo/LiPo HV;Â
Current: 5A continuous peak 6A (3Â seconds);Â
Support BLHeliSuite programmable;Â
Factory firmware: S_H_50_REV16_7.HEX;Â
Default protocol: DSHOT600.Â
Onboard Frsky SPI D8 Receiver Version –Â
SPI BUS receiver Frsky D8 compatible;Â
Compatible Non EU transmitter D8 model;Â
Channels: 8ch;Â
Failsafe support;Â
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m.Â
Onboard Flysky SPI receiver Version –Â
Protocol: AFHDS and AFHDS-2A Switchable;Â
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A);Â
No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m;Â
Failsafe support.Â
Onboard DSM2/X SPI receiver Version –Â
SPI BUS receiver DSM2/DSMX compatible;Â
Channels:Â Max 12ch;Â
Failsafe support;Â
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m;Â
RSSI enable (show on the goggles).Â
Onboard 5.8G 40CH 25/200mW VTX –Â
Output power: 25mw~200mw switchable;Â
Frequency: 40CH;Â
Input voltage: 3.3V 5.5V;Â
Current consumption: 300mA(type);Â
Frequency: 5.8GHz 5bands 40 channels;Â
With Race band;Â
Smartaudio ready.Â
Caddx ANT 1200TVL Camera –Â
Image Sensor: 1/3′ CMOS Sensor;Â
Horizontal Resolution: 1200 TVL;Â
TV System: NTSC or PAL Switchable;Â
IMAGE: 4:3;Â
Synchronization: Internal;Â
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000;Â
S/N Ratio : >52dB (AGC OFF);Â
Video Output: CVBS;Â
Lens: 1.8mm;Â
Min. Illumination: [email protected];Â
Auto Gain Control: YES;Â
BLC: YES;Â
WDR: Global WDR;Â
DNR: 3D DNR;Â
Dimensions: 14*14mm(with bracket to 19*19mm);Â
Wide Power Input: DC 3.7-18V;Â
Work Temperature: -20℃~+60℃;Â
Weight: 2g (N.W.).Â
Features:Â
– 41gram 1-2s brushless Toothpick drone;Â
– New AIO 4in1 CrazybeeX flight controller;Â
– CADDX ANT 1200tvl Camera;Â
– New 1202.5 brushless motor;Â
– XT30 connector;Â
– Compatible with Insta360 Go Camera ( this camera is NOT Included, you can add it by yourself.).Â
Pacakge Included:Â
1x Crux3 Frame and Canopy;Â
1x Optional Receiver;Â
1x F4 Flight Controller AIO 5A ESC Board;Â
1x 5.8G 25-200mW VTX ( built-in Flight controller);Â
4x Happymodel EX1202.5 6400Â KV Motor;Â
4x Gemfan 3018 Propeller CW;Â
4x Gemfan 3018 Propeller CCW;Â
1x Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera;Â
1x Screw Driver;Â
1x Propeller Disassemble Tool;Â
1x Happymodel Handbag.