115mm CrazybeeX FR V2.2 F4 AIO ESC 25/200mW VTX 1-2S 3 Inch Toothpick FPV Racing Drone BNF w/1202.5 Motor Caddx ANT 1200TVL Camera Support Insta360 Go For Discount

Description

115mm CrazybeeX FR V2.2 F4 AIO ESC 25/200mW VTX 1-2S 3 Inch Toothpick FPV Racing Drone BNF w/1202.5 Motor Caddx ANT 1200TVL Camera Support Insta360 Go
Specification: 
Item Name: 115mm F4 OSD 1-2S 3 Inch Toothpick FPV Racing Drone; 
Wheelbase: 115mm; 
Size: 97x97x35mm (without propellers); 
Optional Receiver Version: 
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode); 
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter); 
Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio); 
Weight: 41g (without battery); 
Recommend Lipo Battery: 2s 350mah/400mah/450mah/520mah Battery ( NOT Included). 

EX1202.5 6400KV Motor – 
Configu-ration: 9N12P; 
Stator Diamter: 12mm; 
Stator Length: 2.5mm; 
Shaft Diameter: Φ1.5mm; 
Motor Dimension(Dia.*Len): Φ14*14.5mm; 
Weight: 4.4g; 
No.of Cells(Lipo): 1-2S. 

Gemfan 3018 2-Blade Propeller – 
Center Thickness: 5.5mm; 
Prop Diameter: 76.5mm; 
Center Hole diameter: 1.5mm. 

CrazybeeX FR V2.2 F4 Flight Controller – 
MCU: STM32F411CEU6 (100MHZ, 512K FLASH); 
Sensor: MPU6000 or ICM20689 or BMI270 (SPI connection); 
Board Size: 28.5×28.5mm; 
Power Supply: 1-2S battery input (DC 2.9V-8.7V); 
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready; 
Built-in Betaflight OSD(SPI Control); 
Built-in 5.8G VTX; 
Built-in SPI Frsky/Flysky receiver or no receiver; 
Built-in 5V 1A BEC; 
(Frsky SPI RX Version) CRAZYBEEX FR V2.2 FC  Firmware target: CrazybeeF4FR; 
(Flysky SPI RX Version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS; 
(DSM2/X SPI RX Version)CRAZYBEEX DXS V1.0 FC firmware target: CrazybeeF4DXS; 
(External Frsky RXSR Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX; 
(External TBS CRSF NANO Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX. 

Onboard 5A BL_S 4in1 ESC – 
MCU upgraded to EFM8BB21; 
Power supply: 1S LiPo/LiPo HV; 
Current: 5A continuous peak 6A (3 seconds); 
Support BLHeliSuite programmable; 
Factory firmware: S_H_50_REV16_7.HEX; 
Default protocol: DSHOT600. 

Onboard Frsky SPI D8 Receiver Version – 
SPI BUS receiver Frsky D8 compatible; 
Compatible Non EU transmitter D8 model; 
Channels: 8ch; 
Failsafe support; 
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m. 

Onboard Flysky SPI receiver Version – 
Protocol: AFHDS and AFHDS-2A Switchable; 
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A); 
No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m; 
Failsafe support. 

Onboard DSM2/X SPI receiver Version – 
SPI BUS receiver DSM2/DSMX compatible; 
Channels: Max 12ch; 
Failsafe support; 
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m; 
RSSI enable (show on the goggles). 

Onboard 5.8G 40CH 25/200mW VTX – 
Output power: 25mw~200mw switchable; 
Frequency: 40CH; 
Input voltage: 3.3V 5.5V; 
Current consumption: 300mA(type); 
Frequency: 5.8GHz 5bands 40 channels; 
With Race band; 
Smartaudio ready. 

Caddx ANT 1200TVL Camera – 
Image Sensor: 1/3′ CMOS Sensor; 
Horizontal Resolution: 1200 TVL; 
TV System: NTSC or PAL Switchable; 
IMAGE: 4:3; 
Synchronization: Internal; 
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000; 
S/N Ratio : >52dB (AGC OFF); 
Video Output: CVBS; 
Lens: 1.8mm; 
Min. Illumination: [email protected]; 
Auto Gain Control: YES; 
BLC: YES; 
WDR: Global WDR; 
DNR: 3D DNR; 
Dimensions: 14*14mm(with bracket to 19*19mm); 
Wide Power Input: DC 3.7-18V; 
Work Temperature: -20℃~+60℃; 
Weight: 2g (N.W.). 

Features: 
– 41gram 1-2s brushless Toothpick drone; 
– New AIO 4in1 CrazybeeX flight controller; 
– CADDX ANT 1200tvl Camera; 
– New 1202.5 brushless motor; 
– XT30 connector; 
– Compatible with Insta360 Go Camera ( this camera is NOT Included, you can add it by yourself.). 

Pacakge Included: 
1x Crux3 Frame and Canopy; 
1x Optional Receiver; 
1x F4 Flight Controller AIO 5A ESC Board; 
1x 5.8G 25-200mW VTX ( built-in Flight controller); 
4x Happymodel EX1202.5 6400 KV Motor; 
4x Gemfan 3018 Propeller CW; 
4x Gemfan 3018 Propeller CCW; 
1x Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera; 
1x Screw Driver; 
1x Propeller Disassemble Tool; 
1x Happymodel Handbag.